Pilot jet used in Mikuni Flat Slides and Large Body Round Slides
Mikuni No. VM28/210

Fits flat slide carbs 24 thru 44mm (except Pumpers) and new style Round slide (horizontal mounted main jet)

Will not fit the Small Body Carbs used in OEM applications or "Chinese" Mikunis,
Will NOT fit VM33 (pumper) smooth bore carbs.
Will not fit old style round slide carbs with vertically mounted (inside bowl) main jet


NO RETURNS ON JETS
MAKE SURE PICTURE MATCHES YOUR JET

Main jet for the small body 22mm Small Body Mikuni carbs. Also referred to as "Chinese" Mikunis. These are also what is typically used in Mini-Bike & karts due to the lower cost. M5 x .8mm Thread

Will not fit any other Mikunis (such as Large Body Round Slides, Flat Slides, etc)

Note: Not all Small Body (Chinese) Mikunis use the .8mm Thread. Some (esp those a few years old) use the .75mm Thread. Other than the thread size, the jets are the same. The thread size is close enough that with mild force (and a drop of oil), either jet can be used.


NO RETURNS ON JETS
MAKE SURE PICTURE & THREAD MATCHES YOUR JET

Replacement Dust Cap For A 22 Mikuni. This is The Cap That Covers The Top Air/Fuel Mixing Chamber. The Carb Cable Runs through This.

OEM Jets for Honda Motors And Clones
NO RETURNS ON JETS

These are for Small Body VM22 carbs (i.e. the cheap Chinese ones)

*Will not fit the large body VM22 Japan carbs*

This E-tube has a slightly larger main bore and less air bleed holes providing a better fuel signal at the jet. Improves performance across the RPM range, but especially on bottom end and mid range. You will want a main jet between .035" and .037" and low speed jet around .024" depending on how much you can bore out the carb venturi and which cam you use. This tube is legal in both Superbox and BP. It is not permitted in Box Stock classes. Fits All Honda And Honda Clones

NO RETURNS ON TUBES

This is a Genuine Mikuni Vm22-133  Float Bowl Gasket For Large Round Slide Carbs.

Replacement Cap For A 22 Mikuni. This The Cap That Covers The Air/Fuel Mixing Chamber.

Rebuild Kit for Small Body VM22 carbs (i.e. the cheap Chinese ones)

Will not fit the large body VM22 Japan carbs

Best Quality Stock Carb Replacement for all 6.5 Chinese OHVs. Has a larger Main Bore And Venture Porting

• Intake Inside Diameter: 0.989''
• Air Filter Mount Inside Diameter: 1.37''
• Air Filter Mount Outside Diameter: 1.494''
• Increase the horsepower and airflow for your bike, and have more fun with the power at your finger tips
• Includes a #15 Upgraded Jet Installed
• Main Jet is drilled to 130

Lippo 26mm Carburetor. Great bolt on Carburetor for a Tecumseh 10hp HM100 Engine. This Carb has been Widely Used in the Detroit Metro Area Over the Years.

• 28mm Bore
• Chromed round-flat throttle valve for excellent response and more flow at high RPM.
• Uses standard round slide Mikuni main Jets
• Uses Kehien 21 Series Pilot Jets
• Black crinkle finish
• Fits our flat slide manifolds (hose required)
• 135 Main & stock pilot recommend for most applications

VM 22 Performance Kit to adapt to a Predator 212cc Engine

- Note current air filters are a blue gray color

• Spigot Mount ID: 22mm
• Main Jet: 4/042-100
• Pilot Jet: VM22/210-30
• Needle Jet: N-8 (257)
• Throttle Valve: 2.0 (VM26/21)
• Main Air Jet: 2.5 body
• Needle Valve: 2.0 (VM26/26)
• Carburetors come complete with lever chokes and standard jetting

This Kit Is A Great Performance Upgrade For 5hp Flathead Briggs. Allows You Too Get Rid Of All Stock Linkages And Gas Tank. Already Comes with Upgraded #15 Pilot Jet and #130 Main Jet. #130 Main Jet Requires Installation.

This FLAT SLIDE SMOOTHBORE design cuts down the turbulence in the bore-throat to increase air flow efficiency. Smoothbore design eliminates various orifices and obstacles in the carb throat which cuts down the turbulence to increase air flow efficiency Increases velocity and horsepower Uses standard VM pilot, main and air jets Instantaneous response Comes with built-in location for power jet

( Note: This is A Gas Carb!) This FLAT SLIDE SMOOTH BORE design cuts down the turbulence in the bore-throat to increase air flow efficiency. Smooth bore design eliminates various orifices and obstacles in the carb throat which cuts down the turbulence to increase air flow efficiency Increases velocity and horsepower Uses standard VM pilot, main and air jets Instantaneous response Comes with built-in location for power jet.

MIKUNI AMERICAN CORPORATION TM FLAT SLIDE CARBURETOR 32MM

VM 22 Performance Kit to adapt to a Predator 212cc Engine

- Note current air filters are a blue gray color

MIKUNI AMERICAN CORPORATION TM FLAT SLIDE CARBURETOR 34MMCarburetor For Mikuni TM34 TM 34mm 34 mm Flat Slide Smoothbore Carb TM34-2

MIKUNI AMERICAN CORPORATION TM FLAT SLIDE CARBURETOR 36MM Carburetor

MIKUNI AMERICAN CORPORATION TM FLAT SLIDE CARBURETOR 38MM Carburetor

( Note: This is A Methanol Carb!) This FLAT SLIDE SMOOTH BORE design cuts down the turbulence in the bore-throat to increase air flow efficiency. Smooth bore design eliminates various orifices and obstacles in the carb throat which cuts down the turbulence to increase air flow efficiency Increases velocity and horsepower Uses standard VM pilot, main and air jets Instantaneous response Comes with built-in location for power jet.

The Best Option for GX200s and Chinese OHVs

34mm carb, air filter, intake, hose clamps