Great For Shimming Clutches on Crank Shafts. 14 Gauge (Thick) This Is A machined Washer With Precision Thickness.

Great For Shimming Clutches on Crank Shafts. 1/8" Thick. This Is A machined Aluminium  Washer With Precision Thickness.

Great For Shimming Clutches on Crank Shafts. 1/4" Thick. This Is A machined Aluminium  Washer With Precision Thickness.

Great For Shimming Clutches on Jack Shafts. 1/4" (Thick). This Is A machined Aluminium  Washer With Precision Thickness.

Great For Shimming Jack Shafts. 1/2" Thick. This Is A machined Aluminium  Washer With Precision Thickness.

Used To Connect Brake Cable To Brake Band.

This is the replacement brake cable Adjustment Nuts For The Baja Left All Steel Brake lever With Adjuster 7/8.

Used To Adjust Tension On Brake And Throttle Cables. 8MM fitting.

Cable Adjuster For Adjusting The Slack From Your Throttle Cable

Fits our High Quality Left Side Brake Lever With Adjuster and Full Size Right Side Brake Lever

• 3/8" Large Barrel
• 60" inner cable
• 55" outer casing
• Heavy-duty universal cable
• Barrel on one end

Fits our Doodle Bug Left Spring Loaded Brake Lever 7/8 ( Adjustable), and Vintage Small Left Cast Brake Lever.
All Brake Cable ends can be cut for Custom Applications as needed.Can be used with or without holder.Great For Motovox, Doodle Bug, Monster Moto Etc.

• 1/4" Small BMX Barrel
• 60" conduit
• With Metal Holder

Fits our High Quality Left Side Brake Lever With Adjuster and Full Size Right Side Brake Lever
All Brake Cable ends can be cut for Custom Applications as needed.

• 3/8" Large Barrel
• 60" conduit
• 65" Inner Cable with a .370" barrel end
• 5/64 Inner Cable OD

Brake puck/Pad used in calipers 9597 and 9598 (common Manco, Fox) Manco Mechanical Brake Caliper. If you need the puck that is adheared to the caliper suggest you replace the caliper. This is for one brake puck.

This Vintage Brake Lever Is Great For Old School Mini Bikes Like Ruttmann and Lil Indian. Works on all 7/8 Bars. Uses 3/18 Barrel Cable.

Forged Aluminum Cable Adjuster. Used to Adjust the slack from Brake/Throttle Cables. Also used to Adjusting Clutch Cables On  Honda Style levers.

Universal Brake Cable 56' With Clevis and Spring.

• Fits Fox and Rupp rear wheel
• 56" inner cable
• 51 1/4" outer casing
• Comes with U-clamp and spring

Universal Brake Cable 34' With Clevis and Spring.

• Fits Fox and Rupp rear wheel
• 34" inner cable
• 30' outer casing
• Comes with U-clamp and spring

Universal Parts LEFT brake handle with built in stop switch & wire For use With Our Brake Light Kit.

Custom Color Sleeve Brake Cables. Comes in 6 Colors ( Choose From options Above)
Fits our Doodle Bug Left Spring Loaded Brake Lever 7/8 ( Adjustable), and Vintage Small Left Cast Brake Lever.
All Brake Cable ends can be cut for Custom Applications as needed. Can be used with or without holder. Great For Motovox, Doodle Bug, Monster Moto Etc.

• 1/4" Small BMX Barrel
• 60" conduit
• With Metal Holder

Universal Parts Right brake handle with built in stop switch & wire For use With Our Brake Light Kit.

• 2" Wide
• 4 1/8" Tall
• 3 1/2" Between ears

OEM Brake pad set for Coleman CT200/ Trailmaster/ Baja and other mini bikes (set of two pads as shown)

Spring Loaded Adjustable left Side Doodle Bug Brake lever.  Chrome plated lever. Can be used on any 7/8 Handle Bars.

Trailmaster/MB200 Replacement Brake Lever for New Style With Hydraulic Brake

4-1/2" Drum has 6 holes on a 5-1/4" bolt circle. Machined "OD" for band brakes.
All drums have 3 sets of moutning holes: 3 & 4 hole on a 3.75" diameter bolt circle
and a 4 hole on a 3.228" bolt circle to match the Azusa Mini-Hub.

• Machined OD for Band Brake Use
• 2-1/8" Center Bore
• Fits Our 4.5" Brake Band

4-1/2" Band Brake. Steel Band, 2 Piece bonded brake lining, steel brake pin with cable hole. Band width 7/8"

This is the replacement brake cable for all versions of the Baja Mini Bike including MB165 and MB200. 62" Length. Compatible with many large 6.5 Hp engine mini bikes. Compatible with Baja Left All Steel Brake lever With Adjuster 7/8