Wheelie Bar Tab
Weld On Wheelie Bar Mont Tabs. Can Be Used For other Applications like A Shock Mount.
Wheelie Bar Bracket
Weld On Wheelie Bar Bracket. Can Be Used For other Applications like A Shock Mount.
Tank Mount Bung 5/16th Inc NPT Aluminum
Weld On Tank Mount Bung 5/16th Inch With 24 Thread. These Are Used For Custom made Gas Tanks. These Allow The Tank To Be Mounted To A Frame 5/16 by 24 Thread Screws.
Ruttman Spring Cups (Pair)
Spring cup for 7/8" tubing, to be welded on. Inside diameter is 7/8" and outside diameter is 1-7/8". Use with our OMB_9124 spring! These are raw steel. The cups are NOS parts and may have some surface rust. Sold As A Pair
Mini Bike Kick Stand & Bracket
Universal Kickstand with Weldable Bracket. 4-1/2" from the top to where it hits the ground. 6" total length. Approximate Measurements:
- Overall length: 5-1/8"
- Length before bend: 4"
- Diameter: 1/2"
This must be welded to the frame!!
1" Exhaust, Flange, Header w/stub, GX200
Flange for making your own exhaust,Picture is for reference Only. You will get a header flange with a short piece of pipe welded to it.
Uses 1" Pipe and bends
(Picture For Reference Only)
AZUSA Engine/Motor Adapter Mounting Plate 5" x 12", Flat (11 ga.)
Engine Mounting Plate - 5" x 12" Flat, 11 Gauge Steel
Engine Mounting Plate - 5" x 12" x 0.137 (9/64") 11 gauge with slotted mounting holes.
Product Specs:
- Flat Engine Mounting Plate
- 12" x 5"
- Heavy Gauge Steel
- Slotted Mounting Holes
- Center to Center Distance: 2 3/4" x 5"
- Fits all popular Small Block Engines 3HP-7HP
- Fits Briggs & Stratton
- Tecumseh
- Honda, Honda Clone
- Predator 212cc
1 1/8" Exhaust, Flange, Header w/stub, GX390
Flange for making your own exhaust,Picture is for reference Only. You will get a header flange with a short piece of pipe welded to it.
Uses 1 1/8" Pipe and bends
(Picture For Reference Only)
Harrison Topper Light Duty Engine/Motor Adapter Mounting Plate
This Topper Plate Is Designed To Go Over Existing Engine Plate. Light Duty Steel Plate. Saves you the Trouble Of Grinding Your Old Plate Off. 5/64 Thick, .08. Exact Replacement for A Harrison Mini Bike. Will Fit Standard Small Block Engines Footprint 3-7 Horsepower Engines.
Bottom Fork Plate (Doodlebug, Motovox,Monster Moto)
Bottom Fork Plates For Front Springer Suspension. Top Hole Is 10mm. Two Bottom Fork Holes Are 7/8" Inch.
Top Hole Can Be Drilled Out to 5/8th for Ruttman Or Harrison And Used For Other Mini Bikes As need.
Bottom Width is 10 Inches, Length Is 4 Inches.
Fork Hole Width is 8-1/2" From Center To Center
Fork Hole Diameter 7/8"
Top Fork Plate ( 1/2" Top Hole)
Top Fork Plate For Front Springer Suspension.
The Top Hole is 1/2"
(Top Hole Can Be Drilled Out to 5/8th for Ruttman Or Harrison And Used For Other Mini Bikes As need.)
Bottom Width is 10 Inches, Length Is 4 Inches.
Fork Hole Width is 4' From Center To Center
Fork Hole Diameter 10mm.
Top Fork Plate ( 10'mm Top Hole) Doodlebug, Motovox, And Monster Moto
Top Fork Plate For Front Springer Suspension. Designed for Motovox, Doodlebug, And Monster Moto
The Top Hole is 10'MM
(Top Hole Can Be Drilled Out to 5/8th for Ruttman Or Harrison And Used For Other Mini Bikes As need.)
Bottom Width is 10 Inches, Length Is 4 Inches.
Fork Hole Width is 4' From Center To Center
Fork Hole Diameter 10mm.
Bottom Fork Plate Harrison
Harrison Bottom Fork Plates For Front Springer Suspension. Top Hole Is 1/2". Two Bottom Fork Holes Are 7/8" Inch. Top hole can be drilled out to 5/8'mm or Can Be Modified And Used For Other Mini Bikes As need.
Bottom Width is 10 Inches, Length Is 4 Inches.
Fork Hole Width is 8-1/2" From Center To Center
Fork Hole Diameter 7/8"
Exhaust Bends, Straights & Misc. Pieces 1 1/4" (460cc)
Cant Find The Exhaust Pipe You Need For Your Custom Application? Here's The Parts to Build Your Own! Exhaust bends And Straight for custom applications.
1 1/4 (1.25) " OD pipe with one end flared to 1 1/4" ID
NOTE: THIS IS NOT A FULL KIT. THIS IS INDIVIDUAL PIECES.
(Picture is for reference only. Straight Pipe does NOT have flange. Order flange or stub separate)
7/8" Springer Fork Down Tube
7/8" Diameter Down Tube For Front Springer Forks. 19" Length. Can be Cut To Custom Length As Needed. Made For 5/8' Axle
Big Block Make Your Own Exhaust Kit 1 1/8" ( GX390 And Big Blocks)
The Complete Kit That Includes Everything To Custom Weld Or Clamp The Exhaust You Want.
1 1/8 (1.125) " OD pipe with one end flared to 1 1/8" IDKit Includes: - 180 Degree Bend
- 45 Degree Bend
- 90 Degree Bend
- Straight
- 1 1/8" Exhaust, Flange
(
Picture is for reference only. Straight Pipe does NOT have flange. Order flange or stub separate)